Publikationsliste für
V.-M. Archodoulaki
als Autorin / Autor bzw. wesentlich beteiligte Person
220 Datensätze (2002 - 2022)
Bücher und Buch-Herausgaben
V. Archodoulaki:
"Eigenschaftsänderungen von Polyoxymethylenen induziert durch Verarbeitung, Alterung und Recycling";
VDI Verlag GmbH,
Düsseldorf,
2005,
ISBN: 3-18-370505-2;
232 S.
Zeitschriftenartikel
R. Alessandro, M. Merola, P. Carlone, V. Archodoulaki:
"Tribo-mechanical characterization of reinforced epoxy resin under dry and lubricated contact conditions";
Composites - Part B: Engineering,
79
(2015),
S. 595
- 603.
V. Archodoulaki, M. Jones:
"Recycling viability: A matter of numbers";
Resources, Conservation and Recycling,
168
(2021),
S. 1
- 2.
V. Archodoulaki, T. Koch, A. Rodriguez, S. Seidler:
"Influence of different sterilization procedures on the morphological parameters and mechanical properties of ultra-high-molecular-weight polyethylene";
Journal of Applied Polymer Science,
120
(2011),
4;
S. 1875
- 1884.
Zusätzliche Informationen
V. Archodoulaki, S. Lüftl, T. Koch, S. Seidler:
"Property changes in polyoxymethylene (POM) resulting from processing, ageing and recycling";
Polymer Degradation and Stability,
Vol. 92
(2007),
12;
S. 2181
- 2189.
Zusätzliche Informationen
V. Archodoulaki, S. Lüftl, S. Seidler:
"Degradation Behavior of Polyoxymethylene: Influence of Different Stabilizer Packages";
Journal of Applied Polymer Science,
Vol. 105
(2007),
6;
S. 3679
- 3688.
Zusätzliche Informationen
V. Archodoulaki, S. Lüftl, S. Seidler:
"Effects of Coloration on the Physical and Mechanical Properties and on the Thermal Stability of Polyoxymethylene";
Advances in Polymer Technology,
25
(2006),
1;
S. 63
- 72.
V. Archodoulaki, S. Lüftl, S. Seidler:
"Oxidation induction time studies on the thermal degradation behaviour of polyoxymethylene";
Polymer Testing,
25
(2006),
S. 83
- 90.
V. Archodoulaki, S. Lüftl, S. Seidler:
"Stabiliser consumption of polyoxymethylene investigated by means of the pressure oxidative induction time method";
Polymer Testing,
27/2
(2007),
S. 234
- 242.
V. Archodoulaki, S. Lüftl, S. Seidler:
"Thermal degredation behaviour of poly(oxymethylene): 1. Degradation and stabilizer consumption";
Polymer Degradation and Stability,
86
(2004),
S. 75
- 83.
S. Fröhlich, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"MALDI-TOF Mass Spectrometry Imaging Reveals Molecular Level Changes in Ultrahigh Molecular Weight Polyethylene Joint Implants in Correlation with Lipid Adsorption";
Analytical Chemistry,
86
(2014),
S. 9723
- 9732.
Zusätzliche Informationen
S. Fröhlich, V. Dorrer, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"Synovial Fluid Protein Adsorbtion on Artificial, Polymer-based Hip Joint Material Investigated by MALDI-TOF Mass Spectrometry Imaging";
EuPA Open Proteomics,
4
(2014),
S. 70
- 80.
Zusätzliche Informationen
M. Huber, V. Archodoulaki, E. Pomakhina, B. Pukanszky, E. Zinöcker, M Gahleitner:
"Environmental degradation and formation of secondary microplastics from packaging material: A polypropylene film case study";
Polymer Degradation and Stability,
195
(2022),
109794.
M. Jones, V. Archodoulaki, B. Köck:
"The power of good decisions: Promoting eco-informed design attitudes in plastic selection and use";
Resources, Conservation and Recycling,
182
(2022),
106324;
9 S.
F. Kamleitner, B. Duscher, T. Koch, S. Knaus, V. Archodoulaki:
"Long chain branching as an innovative up-cycling process of polypropylene post-consumer waste - Possibilities and limitations";
Waste Management,
68
(2017),
S. 32
- 37.
Zusätzliche Informationen
F. Kamleitner, B. Duscher, T. Koch, S. Knaus, V. Archodoulaki:
"Upcycling of polypropylene-the influence of polyethylene impurities";
Polymer Engineering and Science,
57
(2017),
12;
S. 1374
- 1381.
Zusätzliche Informationen
F. Kamleitner, B. Duscher, T. Koch, S. Knaus, K. Schmid, V. Archodoulaki:
"Influence of the Molar Mass on Long-Chain-Branching of Polypropylene";
Polymers,
9
(2017),
9.
Zusätzliche Informationen
E. Karaagac, M. Jones, T. Koch, V. Archodoulaki:
"Polypropylene Contamination in Post-Consumer Polyolefin Waste: Characterisation, Consequences and Compatibilisation";
Polymers,
13
(2021),
16;
S. 1
- 12.
E. Karaagac, T. Koch, V. Archodoulaki:
"Choosing an Effective Compatibilizer for a Virgin HDPE Rich-HDPE/PP Model Blend";
Polymers,
13
(2021),
20;
S. 1
- 17.
E. Karaagac, T. Koch, V. Archodoulaki:
"The effect of PP contamination in recycled high-density polyethylene (rPE-HD) from post-consumer bottle waste and their compatibilization with olefin block copolymer (OBC)";
Waste Management,
119
(2021),
1;
S. 285
- 294.
P. Kiss, J. Glinz, W. Stadlbauer, C. Burgstaller, V. Archodoulaki:
"The effect of thermally desized carbon fibre reinforcement on the flexural and impact properties of PA6, PPS and PEEK composite laminates: A comparative study";
Composites - Part B: Engineering,
215
(2021),
S. 1
- 13.
P. Kiss, J. Schoefer, W. Stadlbauer, C. Burgstaller, V. Archodoulaki:
"An experimental study of glass fibre roving sizings and yarn finishes in high-performance GF-PA6 and GF-PPS composite laminates";
Composites - Part B: Engineering,
204
(2021),
108487;
S. 1
- 13.
Zusätzliche Informationen
P. Kiss, W. Stadlbauer, C. Burgstaller, V. Archodoulaki:
"Development of high-performance glass fibre-polypropylene composite laminates: Effect of fibre sizing type and coupling agent concentration on mechanical properties";
Composites Part A: Applied Science and Manufacturing,
138
(2020),
106056;
S. 1
- 11.
P. Kiss, W. Stadlbauer, C. Burgstaller, H. Stadler, S. Fehringer, F. Haeuserer, V. Archodoulaki:
"In-house recycling of carbon- and glass fibre-reinforced thermoplastic composite laminate waste into high-performance sheet materials";
Composites Part A: Applied Science and Manufacturing,
139
(2020),
S. 106110
- 106121.
A. Laska, V. Archodoulaki, B. Duscher:
"Failure analysis of retrieved PE-UHMW acetabular liners";
Journal of the Mechanical Behavior of Biomedical Materials,
61
(2016),
S. 70
- 78.
S. Lüftl, V. Archodoulaki, M. Glantschnig, S. Seidler:
"Influence of coloration on initial material properties and on thermooxidative ageing of a polyoxymethylene copolymer";
Journal of Materials Science,
42
(2007),
S. 1351
- 1359.
S. Lüftl, V. Archodoulaki, T. Koch, S. Seidler:
"Effects of the additive package on the thermal properties of a commercial polyoxymethylene homopolymer";
Journal of Vinyl & Additive Technology,
14
(2008),
1;
S. 21
- 27.
S. Lüftl, V. Archodoulaki, S. Seidler:
"Thermal-oxidative induced degradation behaviour of polyoxymethylene (POM) copolymer detected by TGA/MS*";
Polymer Degradation and Stability,
91
(2006),
S. 464
- 471.
R. Markut-Kohl, V. Archodoulaki, S. Seidler, G. Skrbensky:
"PE-UHMW in hip implants: Properties of Conventional and Crosslinked Prosthetic Components";
Advanced Engineering Materials,
11
(2009),
10;
S. B148
- B154.
A. Örs-Ünsal, V. Archodoulaki:
"Comparison of In-Vivo Performance Characteristics of First- Generation and Second-Generation Cross-Linked and Conventional Explants";
Journal Of Arthroplasty.,
xxx
(2020),
S. 1
- 8.
I. Panaitescu, T. Koch, V. Archodoulaki:
"Accelerated aging of a glass fiber/polyurethane composite for automotive applications";
Polymer Testing,
74
(2019),
S. 245
- 256.
Zusätzliche Informationen
I. Panaitescu, T. Koch, V. Archodoulaki:
"Effects of Temperature, Humidity and Automotive Fluids Exposure on Glass Fiber/Polyurethane Composites";
Polymer Composites,
40
(2019),
6;
S. 2357
- 2367.
Zusätzliche Informationen
M. Petrica, B. Duscher, T. Koch, V. Archodoulaki:
"Impact of surface roughness and contact pressure on wear behaviour of PEEK, POM, and PE-UHMW";
International Journal Of Surface Science And Engineering,
11 (1)
(2017),
S. 65
- 84.
M. Petrica, B. Duscher, T. Koch, V. Archodoulaki:
"Studies on tribological behavior of PEEK and PE-UHMW";
AIP Conference Proceedings - American Institute of Physics,
1779
(2016),
1;
5 S.
Zusätzliche Informationen
M. Petrica, B. Duscher, T. Koch, V. Archodoulaki:
"Tribological investigations on virgin and accelerated aged PE-UHMW";
Tribology International,
87
(2015),
S. 151
- 159.
A. Porabka, V. Archodoulaki, W. Molnar, J. Laska:
"Wear behaviour of polyurethane composites with respect to the other mechanical properties";
World Journal of Engineering,
11
(2014),
2;
S. 139
- 146.
Zusätzliche Informationen
C. Schoberleitner, V. Archodoulaki, T. Koch, S. Lüftl, L. Mateos, M. Vincze, M. Werderitsch, G. Kuschnig:
"Development of a sealing material and robot for automatic socket rehabilitation of grey cast iron pipes in drinking water supply systems";
Water Science & Technology: Water Supply,
4
(2013),
S. 924
- 931.
Zusätzliche Informationen
C. Schoberleitner, V. Archodoulaki, T. Koch, S. Lüftl, M. Werderitsch, G. Kuschnig:
"Developing a Sealing Material: Effect of Epoxy Modification on Specific Physical and Mechanical Properties";
Materials,
6
(2013),
12;
S. 5490
- 5501.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, W. Fidi, A. Holzner, S. Robin:
"Survey of the crack growth approach for the fatigue life estimation of application-relevant rubbers";
AIP Conference Proceedings - American Institute of Physics,
1779
(2016),
1;
5 S.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, A. Holzner, A. Wondracek:
"Ermüdungsverhalten technischer Gummimischungen - Der Einfluss verschiedener Parameter am Beispiel eines anwendungsrelevanten Belastungsfalls";
GAK - Gummi Fasern Kunststoffe,
70
(2017),
4;
S. 234
- 239.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, A. Holzner, A. Wondracek:
"Investigation of different influences on the fatigue behaviour of industrial rubbers";
Polymer Testing,
59
(2017),
S. 99
- 106.
Zusätzliche Informationen
M. Seier, S. Stanic, T. Koch, V. Archodoulaki:
"Effect of Different Compatibilization Systems on the Rheological, Mechanical and Morphological Properties of Polypropylene/Polystyrene Blends";
Polymers,
12
(2020),
2335;
S. 1
- 20.
Zusätzliche Informationen
F. Stadlbauer, T. Koch, V. Archodoulaki, F. Planitzer, W. Fidi, A. Holzner:
"Influence of Experimental Parameters on Fatigue Crack Growth and Heat Build-Up in Rubber";
Materials,
6
(2013),
12;
S. 5502
- 5516.
Zusätzliche Informationen
F. Stadlbauer, T. Koch, F. Planitzer, W. Fidi, V. Archodoulaki:
"Einfluss des Rußfüllgrades von Elastomeren auf Aspekte der Ermüdung in Zug-Druck-Belastung";
Kgk-Kautschuk Gummi Kunststoffe,
66
(2013),
7-8;
S. 37
- 42.
Zusätzliche Informationen
F. Stadlbauer, T. Koch, F. Planitzer, W. Fidi, V. Archodoulaki:
"Setup for evaluation of fatigue crack growth in rubber: Pure shear sample geometries tested in tension-compression mode";
Polymer Testing,
32
(2013),
6;
S. 1045
- 1051.
Zusätzliche Informationen
S. Stanic, G. Gottlieb, T. Koch, L. Göpperl, K. Schmid, S. Knaus, V. Archodoulaki:
"Influence of Different Types of Peroxides on the Long-Chain Branching of PP via Reactive Extrusion";
Polymers,
12
(2020),
886;
S. 1
- 18.
Zusätzliche Informationen
S. Stanic, T. Koch, V. Archodoulaki:
"Improving Rheological and Mechanical Properties of Various Virgin and Recycled Polypropylenes by Blending with Long-Chain Branched Polypropylene";
Polymers,
13
(2021),
7;
S. 1
- 19.
S. Stanic, T. Koch, K. Schmid, S. Knaus, V. Archodoulaki:
"Upcycling of polypropylene with various concentrations of peroxydicarbonate and dilauroyl peroxide and two processing steps";
Journal of Applied Polymer Science,
138
(2021),
28: e50659;
S. 1
- 20.
Buchbeiträge
V. Archodoulaki:
"Rezyklieren von unverstärkten und faserverstärkten Kunststoffen";
in: "Leichtbau: Prinzipien, Werkstoffauswahl und Fertigungsvarianten",
H.P. Degischer, S. Lüftl (Hrg.);
Wiley-VCH,
2009,
ISBN: 978-3-527-32372-2,
S. 302
- 315.
V. Archodoulaki, S. Lüftl:
"Thermal Properties and Flammability of Polyoxymethylene";
in: "Polyoxymethylene Handbook",
herausgegeben von: S. Lüftl, Visakh P.M., S. Chandran; Wiley;
Scrivener Publishing, Wiley,
Beverly, MA,
2014,
ISBN: 978-1-118-38511-1,
S. 257
- 275.
V. Archodoulaki, S. Lüftl, S. Seidler:
"Charakterisierung des Abbauverhaltens von POM am Beispiel von Kfz-Teilen";
in: "Anwenderseminar Thermische Analyse in der Automobilindustrie",
W. Kunze (Hrg.);
TA Instruments,
Alzenau,
2002,
S. 75
- 88.
C. Bierögel, I. Kotter, B. Langer, R. Lach, K. Reincke, V. Archodoulaki, T. Koch:
"Landolt-Börnstein, Volume 6 Polymers, Subvolume A Polymer Solids and Polymer Melts, Part 3 Mechanical and Thermomechanical Properties of Polymers";
in: "Landolt-Börnstein, Volume 6 Polymers, Subvolume A Polymer Solids and Polymer Melts, Part 3 Mechanical and Thermomechanical Properties of Polymers",
Springer,
Berlin,
2014,
ISBN: 978-3-642-55165-9,
S. 34
- 61.
C. Schoberleitner, T. Koch, V. Archodoulaki:
"Epoxy modifications - A novel sealing material for rehabilitation of pipe joints";
in: "Deformation and fracture behaviour of polymer materials",
247;
W. Grellmann, B. Langer (Hrg.);
herausgegeben von: Springer Series in Materials Science;
Springer,
Cham Switzerland,
2017,
ISBN: 978-3-319-41877-3,
S. 243
- 253.
Zusätzliche Informationen
Vorträge und Posterpräsentationen (mit Tagungsband-Eintrag)
V. Archodoulaki:
"Degradation and Stabiliser consumption of thermoplastics";
Hauptvortrag: Polymertec16,
Merseburg (eingeladen);
14.06.2016
- 17.06.2016; in: "Polymertec16",
B. Langer, P. Michel (Hrg.);
(2016),
S. 80.
V. Archodoulaki, B. Duscher, A. Laska:
"Evaluation Of Structural Modification Of Conventional And Crosslinked Pe-Uhmw Acetabular Liners After In-Vivo Use";
Poster: Modest 2016, 9th International Conference on Modification Degradation and Stabilisation of Polymers,
Krakau;
04.09.2016
- 09.09.2016; in: "Modest 2016, 9th International Conference on Modification Degradation and Stabilisation of Polymers",
(2016),
S. 183.
V. Archodoulaki, T. Koch, S. Lüftl:
"Effects of blending polyamide, polypropylene or polyolefin platomer with polyoxymethylene homopolymer on thermal degradation properties";
Poster: MoDeSt (international conference on Modification, Degradation and Stabilisation of polymers),
Prag;
02.09.2012
- 06.09.2012; in: "7th MoDeSt Conference Book of Abstracts",
Academy of Science of the Czech Republic,
Prag
(2012),
ISBN: 978-80-85009-74-3;
2 S.
Zusätzliche Informationen
V. Archodoulaki, T. Koch, S. Lüftl, S. Seidler:
"Auswirkungen von Verarbeitung, Alterung und Rezyklierung auf die Eigenschaften von Polyoxymethylen";
Poster: 11. Problemseminar Deformation und Bruchverhalten von Kunststoffen,
Merseburg/ Germany;
20.06.2007
- 22.06.2007; in: "11. Problemseminar Deformations- und Bruchverhalten von Kunststoffen",
(2007),
5 S.
V. Archodoulaki, T. Koch, S. Lüftl, S. Seidler:
"Oxidationsinduktionszeit/-temperatur Versuche an Polyoxymethylen (POM) zur Untersuchung der thermooxidativen Alterung";
Vortrag: 13. International Conference Polymeric Materials 2008,
Halle;
24.09.2008
- 26.09.2008; in: "Polymeric Materials 2008",
(2008),
ISBN: 978-3-940744-17-3;
S. C22.
V. Archodoulaki, G. Kuschnig, S. Lüftl, M. Werderitsch:
"Silane modified polyether sealant failure in drinking water pipes";
Vortrag: 6th international conference on Modification, Stabilization and Degradation of Polymers,
Athen;
05.09.2010
- 09.09.2010; in: "MoDeSt2010, Athens, Greece, Proceedings",
MoDeSt Hellenic Organizing Committee,
(2010),
ISBN: 978-960-99362-0-0;
2 S.
Zusätzliche Informationen
V. Archodoulaki, A. Laska, A. Kolb:
"PE-UHMW für Hüftprothesen";
Vortrag: polymertec14,
Merseburg Deutschland;
25.06.2014
- 27.06.2014; in: "polymertec14",
(2014),
S. 55
- 61.
V. Archodoulaki, A. Laska, A. Ors Unsal, B. Duscher:
"Evaluation Of Structural Modification Of Conventional And Crosslinked Pe-Uhmw Acetabular Liners After In Vivo Use";
Poster: EUROMAT 2017,
THESSALONIKI;
17.09.2017
- 22.09.2017; in: "EUROMAT 2017",
EUROMAT 2017,
(2017),
Paper-Nr. F4-P-TUE-P1-5,
1 S.
Zusätzliche Informationen
V. Archodoulaki, S. Lüftl, T. Koch, S. Seidler, R. Stoiber:
"Correlation between molar mass and thermal/mechanical properties of polyoxymethylene (POM) copolymers";
Poster: 6th international conference on Modification, Stabilization and Degradation of Polymers,
Athen, Griechenland;
05.09.2010
- 09.09.2010; in: "MoDeSt2010, Athens, Greece, Proceedings",
MoDeSt Hellenic Organizing Committee,
(2010),
ISBN: 978-960-99362-0-0;
2 S.
Zusätzliche Informationen
V. Archodoulaki, S. Lüftl, S. Seidler:
"Effects of Processing, Ageing and Recycling on the Properties of Polyoxymethylene (POM)";
Poster: 8th Austrian Polymer Meeting,
Linz, Austria;
20.09.2006
- 22.09.2006; in: "8th Austrian Polymer Meeting. The Chain of Knowledge - From Catalyst to Application",
(2006),
S. 48.
V. Archodoulaki, S. Lüftl, S. Seidler:
"Influence of coloration on the thermal degredation behaviour of artificially aged Polyoxymethylene (POM)";
Poster: Third International Conference on Polymer Modification, Degradation and Stabilisation (MoDeSt 3),
Lyon, France;
29.08.2004
- 02.09.2004; in: "MoDeSt 3. Third International Conference on Polymer Modification, Degradation and Stabilisation",
(2004),
4 S.
V. Archodoulaki, S. Lüftl, S. Seidler:
"Photooxidative Degradation of Polyoxymethylene (POM)";
Poster: 11. Internationale Fachtagung Polymerwerkstoffe 2004,
Halle/Saale;
29.09.2004
- 01.10.2004; in: "Polymeric Materials 2004. Abstracts",
G. H. Michler (Hrg.);
(2004),
ISBN: 3-928466-68-2;
S. PI-73.
V. Archodoulaki, S. Lüftl, S. Seidler:
"Property changes of polyoxymethylene (POM) by means of processing, ageing and recycling";
Vortrag: Fourth International Conference on Polymer Modification, Degradation and Stabilization (M2o06 DeSt),
San Sebastian, Spain;
10.09.2006
- 14.09.2006; in: "Fourth International Conference on Polymer Modification, Degradation and Stabilization - Book of Abstracts",
(2006),
S. 93.
V. Archodoulaki, S. Lüftl, S. Seidler:
"Thermal-oxidative induced degradation behaviour of Polyoxymethylene (POM) copolymer detected by TGA/MS";
Vortrag: Third International Conference on Polymer Modification, Degradation and Stabilisation (MoDeSt 3),
Lyon, France;
29.08.2004
- 02.09.2004; in: "MoDeSt 3. Third International Conference on Polymer Modification, Degradation and Stabilisation",
(2004),
4 S.
V. Archodoulaki, S. Lüftl, M. Spitzbart, S. Seidler:
"Determination of Oxidation Induction Time and Oxidation Induction Temperature (OIT) for Polyoxymethylene";
Vortrag: 6th Austrian Polymer Meeting, Wien (Austria),
Wien (Austria);
15.09.2003
- 17.09.2003; in: "6th Austrian Polymer Meeting, Wien (Aurstria)",
Wien (Austria)
(2003),
S. 72.
V. Archodoulaki, S. Lüftl, M. Spitzbart, S. Seidler:
"What You Should Avoid in the Application of Polymer Thermal Analysis (A Day in a Thermoanalytic Laboratory)";
Poster: 6th Austrian Polymer Meeting, Wien (Austria),
Wien (Austria);
15.09.2003
- 17.09.2003; in: "6th Austrian Polymer Meeting, Wien (Austria)",
Wien (Austria)
(2003),
S. 167.
V. Archodoulaki, R. Markut-Kohl, T. Koch, S. Seidler:
"Characterisation of the fracture behaviour and determination of micro-hardness of medical grade ultra high molecular weight polyethylene (PE-UHMW)";
Vortrag: 6th international conference on Modification, Stabilization and Degradation of Polymers,
Athen, Griechenland;
05.09.2010
- 09.09.2010; in: "MoDeSt2010, Athens, Greece, Proceedings",
MoDeSt Hellenic Organizing Committee,
(2010),
ISBN: 978-960-99362-0-0;
2 S.
Zusätzliche Informationen
V. Archodoulaki, M. Merola, D. Kastanis, T. Koch, P. Carlone:
"Influence of the impregnation velocity on impregnation quality and mechanical properties of Vacuum Assisted Resin Transfer Moulding (VARTM) Materials";
Vortrag: 20. Symposium Verbundwerkstoffe und Werkstoffverbunde 2015,
Wien;
01.07.2015
- 03.07.2015; in: "20th Symposium on Composites",
C. Edtmaier, G. Requena (Hrg.);
Materials Science Forum,
Vol. 825-826
(2015),
ISBN: 978-3-03835-515-1;
S. 36
- 43.
B. Duscher, V. Archodoulaki, A. Laska, S. Seichter, A. Örs Ünsal:
"Bestimmung struktureller Änderungen in Hüftgelenkinlays aus konventionellem und vernetztem PE-UHMW nach in vivo-Gebrauch";
Poster: Tagung Werkstoffprüfung 2015,
Bad Neuenahr;
02.12.2015
- 04.12.2015; in: "Fortschritte in der Werkstoffprüfung für Forschung und Praxis",
Verlag Stahleisen,
Düsseldorf
(2015),
ISBN: 978-3-514-00816-8;
S. 285
- 290.
C. Fleischberger, V. Archodoulaki, I. Steiner:
"Active food packaging materials containing citric acid and sorbic acid";
Poster: 5th International Symposium on Food Packaging,
Berlin;
14.11.2012
- 16.11.2012; in: "Food Packaging - Scientific Developments Supporting Safety and Innovation",
ILSI Europe (Hrg.);
(2012),
S. 122.
Zusätzliche Informationen
C. Fleischberger, V. Archodoulaki, I. Steiner:
"Influence Of Active Packaging Materials On Microorganisms Of Selected Food Stuffs";
Poster: Eurofoodchem Xvii,
Istanbul;
07.05.2013
- 10.05.2013; in: "Eurofoodchem Xvii - Book of Abstracts",
H. Köksel (Hrg.);
(2013),
ISBN: 978-605-63935-0-1;
S. 695.
Zusätzliche Informationen
C. Fleischberger, V. Archodoulaki, I. Steiner:
"Mikrobiologisch wirksame Substanzen in "aktiven" Lebensmittel-Verpackungsfolien";
Vortrag: Österreichische Lebensmittelchemikertage 2012,
Linz;
25.04.2012
- 27.04.2012; in: "Haltbarkeit von Lebensmitteln",
F. Bauer (Hrg.);
Gesellschaft Österreichischer Chemiker, 1010 Wien,
Tagungsband der Österreichischen Lebensmittelchemikertage 2012
(2012),
ISBN: 978-3-900554-705;
S. 12
- 17.
Zusätzliche Informationen
S. Fröhlich, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"Protein adsorption on ultra-high molecular weight polyethylene joint - Proteomics correlated to MALDI imaging mass spectrometry data";
Poster: EUPA/BSPR Proteomics Meeting 2012,
Glasgow, UK;
09.07.2012
- 12.07.2012; in: "EUPA/BSPR Proteomic Meeting 2012 - Book of Abstracts",
(2012),
S. P147.
S. Fröhlich, L. Dekker, O. Belgacem, A. Barnes, T. Luider, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"Correlating surface changes of UHMW-PE hip joint explants to time-dependent biomolecule adsorption by MALDI-TOF imaging mass spectrometry";
Vortrag: 60th ASMS conference,
Vancouver, CAN;
20.05.2012
- 24.05.2012; in: "Proceedings of the 60th American Society of Mass Spectrometry Conference",
American Society of Mass Spectrometry,
(2012),
Paper-Nr. WOF 8:30 am, 254.
S. Fröhlich, M. Kennedy, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"Lipid adsorption and diffusion correlated with UHMW-PE modifications investigated by MALDI mass spectrometry imaging, ion mobility separation and CID";
Vortrag: 31th Informal Meeting on Mass Spectrometry (IMMS2013),
Palermo, Italien;
05.05.2013
- 08.05.2013; in: "Book of Abstract",
(2013),
ISBN: 978-88-907388-2-1;
S. 38.
Zusätzliche Informationen
J. Gahler, M. Marchetti-Deschmann, R. Markut-Kohl, V. Archodoulaki, G. Allmaier:
"Imaging mass spectrometry of ultr high molecular weight polyethylene explantates";
Vortrag: 4. Wiener Biomaterialsymposium: Von der Werkstoffentwicklung bis zur klinischen Anwendung,
TU Wien, Wien (eingeladen);
15.11.2010
- 17.11.2010; in: "4. Wiener Biomaterialsymposium - Abstractbuch",
(2010),
S. 55.
F. Kamleitner, B. Duscher, T. Koch, V. Archodoulaki:
"Successive self-nucleation and annealing as smart tool for characterization of chemical- and mechanical modified polypropylenes";
Poster: DVSPM 2015,
Gmunden;
11.05.2015
- 13.05.2015; in: "Danube Vltava Sava Polymer Meeting - DVSPM 2015",
Trauner Verlag,
(2015),
ISBN: 9783990334911;
S. 107.
Zusätzliche Informationen
F. Kamleitner, B. Duscher, T. Koch, V. Archodoulaki:
"Upcycling of polypropylene - the influence of polymeric impurities on the mechanical properties";
Vortrag: Modest 2016, 9th International Conference on Modification Degradation and Stabilisation of Polymers,
Krakau;
04.09.2016
- 09.09.2016; in: "Modest 2016, 9th International Conference on Modification Degradation and Stabilisation of Polymers",
(2016),
ISBN: 9788392562733;
S. 129.
Zusätzliche Informationen
F. Kamleitner, B. Duscher, T. Koch, S. Knaus, V. Archodoulaki:
"Chemical modification of polypropylene post-consumer waste by reactive extrusion as an innovative upocycling process";
Vortrag: Polymer Processing Society Conference 2015,
Graz;
21.09.2015
- 25.09.2015; in: "Regional Conference Polymer Processing Society Graz 2015",
Graz
(2015),
S. 333.
Zusätzliche Informationen
F. Kamleitner, B. Duscher, T. Koch, S. Knaus, V. Archodoulaki:
"Innovative upcycling of polypropylene";
Vortrag: Polymertec16,
Merseburg;
14.06.2016
- 17.06.2016; in: "Polymertec16",
(2016),
S. 28.
Zusätzliche Informationen
F. Kamleitner, B. Duscher, T. Koch, S. Knaus, V. Archodoulaki:
"Long Chain Branching as an innovative tool for the up-cycling of Polypropylene post-consumer waste";
Poster: DVSPM 2017,
Wien;
05.09.2017
- 08.09.2017; in: "Danube Vltava Sava Polymer Meeting 2017 DVSPM",
Austria
(2017),
ISBN: 978-3-9504017-6-9;
S. PO-2.
Zusätzliche Informationen
F. Kamleitner, B. Duscher, T. Koch, S. Knaus, V. Archodoulaki:
"Melt functionalisation of polypropylene as an innovative up-cycling process";
Poster: EUROMAT 2017,
THESSALONIKI;
17.09.2017
- 22.09.2017; in: "EUROMAT 2017",
EUROMAT 2017,
(2017),
Paper-Nr. A3-P-TUE-P1-5,
1 S.
Zusätzliche Informationen
E. Karaagac, V. Archodoulaki, B. Duscher:
"Rheological Studies Of Pp/pe Layers And Pp/pe Blends With Compatibilisizers";
Poster: DVSPM 2017,
Wien;
05.09.2017
- 08.09.2017; in: "Danube Vltava Sava Polymer Meeting 2017 DVSPM",
Austria
(2017),
ISBN: 978-3-9504017-6-9;
S. PO-38.
A. Laska, A. Kolb, V. Archodoulaki:
"Studies of the in-vivo use on the physical and mechanical properties of conventional and crosslinked UHMWPE";
Vortrag: 5. Wiener Biomaterialsymposium,
Wien;
19.11.2012
- 21.11.2012; in: "5th Vienna Biomaterialsymposium Abstracts",
(2012),
S. 47.
S. Lüftl, V. Archodoulaki, T. Koch, S. Seidler:
"Correlation between molar mass and thermal properties of polyoxymethylene (POM) homopolymers";
Poster: Polymeric Materials 2012,
Halle (Saale);
12.09.2012
- 14.09.2012; in: "Abstracts",
(2012),
ISBN: 978-3-86829-517-7;
S. 113.
S. Lüftl, V. Archodoulaki, S. Seidler:
"Ageing Behaviour of Multiple Processed Poly(oxymethylene)";
Poster: Polymerwerkstoffe 2002,
Halle (Saale);
25.09.2002
- 27.09.2002; in: "Polymerwekstoffe 2002",
(2002),
S. 118.
S. Lüftl, V. Archodoulaki, S. Seidler:
"Einfluss der Stabilisierung auf die thermischen eigenschaften von Polyoxymethylen (POM)";
Poster: Werkstoffprüfung 2005,
Berlin (Germany);
01.12.2005
- 02.12.2005; in: "Tagungsband Werkstoffprüfung 2005: Herausforderungen neuer Werkstoffe an die Forschung und Werkstoffprüfung (DVM Bericht 641)",
W. Grellmann (Hrg.);
DVM,
(2005),
ISSN: 1861-8154;
S. 305
- 310.
S. Lüftl, V. Archodoulaki, S. Seidler:
"Thermal-Oxidative Induced Degradation Behaviour of Polyoxymethylene (POM) Detected by TGA-MS";
Vortrag: 2nd International Conference on Polymer Modification, Degraddation and Stabilisation,
Budapest;
30.06.2002
- 04.07.2002; in: "MoDeSt 2002 - Second Int. Conference on Polymer Modifiaction, Degraddation and Stabilisation",
CD
(2002).
S. Lüftl, V. Archodoulaki, S. Seidler, M. Glantschnig:
"Charakterisierung des Einflusses von Farbmasterbatches auf die thermischen und mechanischen Eigenschaften von Bauteilen aus einem Polyoxymethylen(POM)-Copolymer";
Vortrag: 11. Internationale Fachtagung Polymerwerkstoffe 2004,
Halle/Saale;
29.09.2004
- 01.10.2004; in: "Polymeric Materials 2004. Abstracts.",
G. H. Michler (Hrg.);
(2004),
ISBN: 3-928466-68-2;
S. C25.
S. Lüftl, V. Archodoulaki, S. Seidler, M. Glantschnig:
"Influence of Coloration on Photo- and Photooxidative Degradation of Polyoxymethylene (POM)";
Vortrag: 6th Austrian Polymer Meeting,
Wien (Austria);
15.09.2003
- 17.09.2003; in: "6th Austrian Polymer Meeting, Wien (Austria)",
(2003),
S. 71.
S. Lüftl, V. Archodoulaki, S. Seidler, M. Glantschnig:
"Influence of the Specimen Shape on Physical Testing Results of Polyoxymethylene (POM) Exposed to Thermooxidative Stresses";
Poster: 6th Austrian Polymer Meeting, Wien (Austria),
Wien (Austria);
15.09.2003
- 17.09.2003; in: "6th Austrian Polymer Meeting",
(2003),
S. 159.
S. Lüftl, V. Archodoulaki, S. Seidler, M. Glantschnig:
"Influence of the Specimen Shape on Physical Testing Results of Polyoxymethylene (POM) Exposed to Thermooxidative Stresses";
Vortrag: 18th Bratislava International Conference on Modified Polymers (ModPol 2003),
Stara Lesna (Slovakia);
05.10.2003
- 08.10.2003; in: "18th Bratislava International Conference on Modified Polymers (ModPol 2003)",
Stara Lesna (Slovakia)
(2003),
ISBN: 80-968433-2-x;
S. 31.
S. Lüftl, V. Archodoulaki, S. Seidler, T. Koch:
"Effects of the additive package on the thermal properties of a commercial Polyoxymethylene (POM) homopolymer";
Poster: 10. Problemseminar Deformations- und Bruchverhalten von Kunststoffen,
Merseburg (Germany);
15.06.2005
- 17.06.2005; in: "10. Problemseminar Deformations- und Bruchverhalten von Kunststoffen",
(2005),
1 S.
S. Lüftl, V. Archodoulaki, S. Seidler, T. Koch:
"Effects of the additive package on the thermal properties of a commercial Polyoxymethylene (POM) homopolymer";
Vortrag: 7th Austrian Polymer Meeting,
Graz, Austria;
04.07.2005
- 06.07.2005; in: "7th Austrian Polymer Meeting",
Institute for Chemistry and Technology of Organic Materials, Graz University of Technology,
(2005),
S. 53.
M. Marchetti-Deschmann, J. Gahler, V. Archodoulaki, G. Allmaier:
"Ultra-high Molecular Weight Polyethylene (PE-UHMW) Joint Implants - Choosing the Most Valuable Desorption Process (i/vMALDI and DESI) for Imaging MS";
Poster: 58th ASMS Conference on Mass Spectrometry and Allied Topics,
Salt Lake City, UT, USA;
23.05.2010
- 28.05.2010; in: "Proceedings of the 58th ASMS Conference on Mass Spectrometry and Allied Topics",
(2010),
Paper-Nr. TP23 534 (1482),
1 S.
R. Markut, V. Archodoulaki, S. Seidler:
"PE-UHMW in Hip Implants: Non-Crosslinked and Highly Crosslinked Prosthetic Components";
Vortrag: 1st Joint Austrian & Slovenian Polymer Meeting ASPM 2008 and 9th Austrian Polymer Meeting,
Graz (eingeladen);
26.03.2008
- 28.03.2008; in: "ASPM 2008 - 9th Austrian Polymer Meeting",
(2008),
S. 37.
R. Markut, V. Archodoulaki, S. Seidler:
"PE-UHMWP in hip implants: The influence of crosslinking on structural parameters and micro-mechanical properties";
Poster: 13. International Conference Polymeric Materials 2008,
Halle;
24.09.2008
- 26.09.2008; in: "Polymeric Materials 2008",
(2008),
ISBN: 978-3-940744-17-3;
S. PI-18.
R. Markut, A. Rodriguez, V. Archodoulaki, S. Seidler:
"Werkstoffcharakterisierung und Schadensanalyse von Implantaten aus PE-UHMW";
Vortrag: 11. Problemseminar Deformation und Bruchverhalten von Kunststoffen,
Merseburg;
20.06.2007
- 22.06.2007; in: ""11. Problemseminar Deformations- und Bruchverhalten von Kunststoffen"",
(2007),
8 S.
R. Markut-Kohl, V. Archodoulaki, T. Koch, S. Seidler:
"The effect of the consolidation process on structural parameters and micromechanical properties of PE-UHMW";
Poster: 4th International Meeting - UHMWPE for arthroplasty: from powder to debris,
Torino, Italy;
16.09.2009
- 17.09.2009; in: "4th International Meeting - UHMWPE for arthroplasty: from powder to debris;",
(2009).
R. Markut-Kohl, V. Archodoulaki, S. Seidler:
"Eigenschaften vernetzter und konventioneller PE-UHMW Werkstoffe für die orthopädische Anwendung";
Vortrag: 12. Problemseminar Deformation und Bruch,
Merseburg;
24.06.2009
- 26.06.2009; in: "tagungsband_12_Problemseminar",
(2009),
8 S.
R. Markut-Kohl, V. Archodoulaki, S. Seidler:
"Influence of the consolidation and crosslinking processes on the properties of orthopaedic grade PE-UHMW";
Vortrag: European Polymer Congress 2009,
Graz;
12.07.2009
- 17.07.2009; in: "epf´09 european polymer congress",
(2009),
S. 112.
R. Markut-Kohl, V. Archodoulaki, S. Seidler:
"PE-UHMW IN IMPLANTS: Influence of processing on the chemical and physical structure";
Vortrag: 2nd Workshop Biotribology - Bridging Engineering and Medicine; Final Meeting COST 533 Action,
Guimarães, Portugal;
25.05.2009
- 27.05.2009; in: "Biotribology - Bridging Engineering and Medicine",
(2009),
S. 16.
R. Markut-Kohl, V. Archodoulaki, S. Seidler, G. Skrbensky:
"PE-UHMW in der Endoprothetik: Eigenschaften vernetzter und nicht vernetzter Implantatteile";
Vortrag: 3. Wiener Biomaterialsymposium,
Wien;
19.11.2008
- 21.11.2008; in: "3. Wiener Biomaterialsymposium, 19.-21.11.2008",
(2008),
ISBN: 978-3-200-01613-2;
S. 32.
R. Markut-Kohl, T. Koch, V. Archodoulaki, S. Seidler:
"PE-UHMW in hip implants: The influence of crosslinking on structural parameters and micro-mechanical properties";
Poster: Cost 533 Training School,
Paris;
04.05.2009
- 08.05.2009; in: "Cost 533 Training School - Biotribology. Basis And Trends In Medicine And Engineering And Its Societal Impact",
(2009),
1 S.
R. Markut-Kohl, T. Koch, V. Archodoulaki, S. Seidler:
"PE-UHMW in hip implants: The influence of crosslinking on structural parameters and mirco-mechanical properties";
Poster: Junior Scientist Conference,
Wien;
16.11.2008
- 18.11.2008; in: "Junior Scientist Conference 2008: Proceedings",
(2008),
ISBN: 978-3-200-01612-5;
S. 209
- 210.
R. Markut-Kohl, M. Mosbeck, V. Archodoulaki, T. Koch, S. Seidler:
"Hüftpfanneneinsätze aus PE-UHMW: Morphologie und Mechanische Eigenschaften";
Vortrag: 4. Wiener Biomaterialsymposium,
Wien;
15.11.2010
- 17.11.2010; in: "Tagungsband - 4. Wiener Biomaterialsymposium",
(2010),
S. 19.
R. Markut-Kohl, M. Mosbeck, V. Archodoulaki, S. Seidler:
"Charakterisierung des mechanischen Verhaltens von Hüftpfannen aus PE-UHMW";
Vortrag: 13. Problemseminar Deformation und Bruchverhalten von Kunststoffen,
Halle-Merseburg;
29.06.2011
- 01.07.2011; in: "13. Problemseminar Deformation und Bruchverhalten von Kunststoffen",
(2011),
6 S.
R. Markut-Kohl, C. Schoberleitner, V. Archodoulaki, S. Seidler, G. Reinisch, A. Kolb:
"Chemical and morphological parameters in crosslinked PE-UHMW: influence of manufacturing and in vivo use on hip implants";
Vortrag: 10th Austrian Polymer Meeting and 2nd Austrian-Slowenian Polymer Meeting,
Leoben;
08.09.2010
- 10.09.2010; in: "ASPM2010 Austrian-Slovenian Polymer Meeting, Leoben 2010: Book of Abstracts",
(2010),
S. 78
- 79.
R. Markut-Kohl, C. Schoberleitner, V. Archodoulaki, S. Seidler, G. Reinisch, A. Kolb:
"Crosslinked PE-UHMW in hip implants: influence of manufacturing and use on structural parameters";
Vortrag: 14th International Conference Polymeric Materials,
Halle (Saale);
15.09.2010
- 17.09.2010; in: "14th International Conference Polymeric Materials",
(2010),
ISBN: 978-3-86829-282-4;
S. 45.
A. Örs Ünsal, M. Petrica, V. Archodoulaki:
"Effect of Progressive Accelerated Aging on PE-UHMW used in Medical Applications";
Poster: Modest 2016, 9th International Conference on Modification Degradation and Stabilisation of Polymers,
Krakau;
04.09.2016
- 08.09.2016; in: "Modest 2016, 9th International Conference on Modification Degradation and Stabilisation of Polymers",
(2016),
S. 133.
A. Ors Unsal, B. Duscher, V. Archodoulaki:
"Characterisation of conventional and crosslinked UHMWPE used in hip joint endoprothesis";
Vortrag: DVSPM 2017,
Wien;
05.09.2017
- 08.09.2017; in: "Danube Vltava Sava Polymer Meeting 2017 DVSPM",
Austria
(2017),
ISBN: 978-3-9504017-6-9;
S. OP-66.
I. Panaitescu, T. Koch, V. Archodoulaki:
"The Effects Of Temperature, Humidity And Automotive Fluids Exposure On A Glass Fibre/polyurethane Composite";
Poster: DVSPM 2017,
Wien;
05.09.2017
- 08.09.2017; in: "Danube Vltava Sava Polymer Meeting 2017 DVSPM",
Austria
(2017),
ISBN: 978-3-9504017-6-9;
S. PO-46.
M. Petrica, J. Schenkyr, A. Örs Ünsal, T. Koch, V. Archodoulaki:
"The influence of morphological changes induced by different cooling rates on the wear behaviour of thermoplastics";
Poster: Polymertec16,
Merseburg;
14.06.2016
- 17.06.2016; in: "Polymertec16",
B. Langer, P. Michel (Hrg.);
(2016),
S. 135.
A. Porabka, K. Jurkowski, J. Laska, F. Stadlbauer, V. Archodoulaki:
"Determination of the Influence of Fly Ash Particles on the Properties of Low-Density Polyethylene";
Poster: ICSAAM 2013,
Island of Kos Greece;
23.09.2013
- 26.09.2013; in: "ICSAAM 2013, Conference Proceedings",
(2013),
2 S.
J. Roitner, V. Archodoulaki:
"Betrachtung des Degradationsverhaltens von Polyethylenen im mechanischen Recycling";
Vortrag: Polymertec 2021,
Merseburg;
09.06.2021
- 11.06.2021; in: "Internationale wissenschaftliche Tagung Polymertec 2021digital",
(2021),
ISBN: 978-3-00-069372-4;
S. 78.
C. Schoberleitner, V. Archodoulaki, T. Koch, S. Lüftl, G. Kuschnig, M. Werderitsch:
"Evaluation of polymer based sealing materials for socket rehabilitation";
Poster: Polymeric Materials 2012,
Halle (Saale);
12.09.2012
- 14.09.2012; in: "Polymeric Materials 2012",
(2012),
7 S.
Zusätzliche Informationen
C. Schoberleitner, V. Archodoulaki, T. Koch, S. Lüftl, L. Mateos, M. Vincze, G. Kuschnig, M. Werderitsch:
"Lead joint socket rehabilitation of grey cast iron pipes in drinking water supply systems";
Vortrag: Water Loss Europe 2012,
Ferrara;
23.05.2012
- 25.05.2012; in: "Water Loss Europe 2012",
(2012),
Paper-Nr. 68,
10 S.
Zusätzliche Informationen
C. Schoberleitner, V. Archodoulaki, T. Koch, S. Lüftl, M. Werderitsch, G. Kuschnig:
"Developing a Sealing Material: Effect of Epoxy Modification on the Specific Physical and Mechanical Properties";
Vortrag: 5th International Conference on Structural Analysis of Advanced Materials,
Kos, Griechenland;
23.09.2013
- 26.09.2013; in: "ICSAAM 2013, Conference Proceedings",
(2013),
12 S.
Zusätzliche Informationen
C. Schoberleitner, T. Koch, V. Archodoulaki:
"Modifizierte Epoxidharze für die Sanierung von Trinkwasserrohren";
Vortrag: Internationale wissenschaftliche Tagung Polymerwerkstoffe, Polymertec 2014,
Merseburg, Deutschland;
25.06.2014
- 27.06.2014; in: "Internationale wissenschaftliche Tagung Polymerwerkstoffe, Polymertec 2014",
(2014),
8 S.
C. Schoberleitner, M. Werderitsch, V. Archodoulaki, T. Koch, G. Kuschnig, S. Lüftl, L. Mateos, M. Vincze:
"Developing Water Loss Prevention - Entwicklung eines Dichtungswerkstoffes / Roboter für die automatisierte Muffensanierung von Graugussrohren im Trinkwasserbereich";
Vortrag: ÖGL Symposium Grabenlos 2012,
Kitzbühel;
16.10.2012
- 17.10.2012; in: "ÖGL Symposium Grabenlos 2012",
(2012),
S. 110
- 122.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch:
"Measurement set-up to investigate the crack nucleation and crack growth approach for the estimation of the fatigue life of rubber";
Vortrag: DVSPM 2015,
Gmunden;
11.05.2015
- 13.05.2015; in: "Danube Vltava Sava Polymer Meeting - DVSPM 2015, Proceedings of a Conference on Polymer Science",
M. List, C. Paulik, Z. Major, I. Teasdale, O. Brüggemann (Hrg.);
Trauner Verlag,
Linz
(2015),
ISBN: 978-3-99033-491-1;
S. 81.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, W. Fidi, A. Holzner:
"The experimentally survey of the crack growth approach for the fatigue life estimation of application-relevant rubbers";
Vortrag: Polymer Processing Society Conference 2015,
Graz;
21.09.2015
- 25.09.2015; in: "Regional Conference Polymer Processing Society Graz 2015",
C. Holzer, S. Laske, M. Payer (Hrg.);
Graz
(2015),
S. 208.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, W. Fidi, A. Holzner, S. Robin:
"Einfluss der Temperatur auf die Ermüdung von Elastomeren";
Vortrag: Tagung Werkstoffprüfung 2015,
Bad Neuenahr, Deutschland;
02.12.2015
- 04.12.2015; in: "Fortschritte in der Werkstoffprüfung für Forschung und Praxis",
M. Borsutzki, G. Moninger (Hrg.);
Verlag Stahleisen,
Düsseldorf
(2015),
ISBN: 978-3-514-00816-8;
S. 61
- 66.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, W. Fidi, A. Holzner, S. Robin:
"Experimental survey of approaches to estimate the uniaxial fatigue life of industrial rubbers";
Vortrag: 9th European Conference on Constitutive Models for Rubbers,
Prag, Tschechien;
01.09.2015
- 04.09.2015; in: "Constitutive Models for Rubber IX",
B. Marvalová, I. Petríková (Hrg.);
CRC Press,
London
(2015),
ISBN: 978-1-138-02873-9;
S. 433
- 438.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, A. Holzner, A. Wondracek:
"A Study On The Fatigue Behaviour Of Industrial Rubbers And Rubber Composites";
Vortrag: 12th Fall Rubber Colloquium KHK,
Hannover, Deutschland;
22.11.2016
- 24.11.2016; in: "12. Kautschuk-Herbst Kolloquium - 12th Fall Rubber Colloquium",
(2016),
S. 65.
S. Seichter, V. Archodoulaki, T. Koch, A. Holzner, A. Wondracek:
"Fatigue Behaviour of Industrial Rubber Blends and Rubber-Textile Composites";
Poster: EUROMAT 2017,
THESSALONIKI;
17.09.2017
- 22.09.2017; in: "EUROMAT 2017",
EUROMAT 2017,
(2017),
Paper-Nr. B10-P-TUE-P1-5,
1 S.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, A. Holzner, A. Wondracek:
"Fatigue Behaviour of Industrial Rubber Blends and Rubber-Textile Composites";
Poster: DVSPM 2017,
Wien;
17.09.2017
- 22.09.2017; in: "Danube Vltava Sava Polymer Meeting 2017 DVSPM",
DVSPM 2017,
Austria
(2017),
ISBN: 978-3-9504017-6-9;
S. PO-32.
Zusätzliche Informationen
S. Seichter, V. Archodoulaki, T. Koch, A. Holzner, A. Wondracek:
"Investigation of different influences on the fatigue behaviour of industrial rubber blends";
Vortrag: Polymertec16,
Merseburg;
15.06.2016
- 17.06.2016; in: "Internationale wissenschaftliche Tagung Polymerwerkstoff Polymertec16",
B. Langer, P. Michel (Hrg.);
(2016),
S. 20.
Zusätzliche Informationen
M. Seier, V. Archodoulaki:
"Challenges in mechanical recycling of single-use plastics and possibilities of new concepts";
Poster: EUROMAT 2021,
Online;
13.09.2021
- 17.09.2021; in: "European Congress And Exhibition On Advanced Materials And Processes - Euromat 2021",
(2021).
M. Seier, V. Archodoulaki:
"Herausforderungen im mechanischen Recycling von Einweg-Kunststoffen und Möglichkeiten neuer Konzepte";
Vortrag: Polymertec 2021,
Merseburg;
09.06.2021
- 11.06.2021; in: "Internationale wissenschaftliche Tagung Polymertec 2021digital",
(2021),
ISBN: 978-3-00-069372-4;
S. 44.
F. Stadlbauer, T. Koch, V. Archodoulaki:
"Approach to Measure the Influence of Experimental Parameters on Fatigue Crack Growth and Heat Build-Up in Rubber";
Vortrag: 5th International Conference on Structural Analysis of Advanced Materials,
Kos, Griechenland;
23.09.2013
- 26.09.2013; in: "ICSAAM 2013, Conference Proceedings",
(2013),
15 S.
Zusätzliche Informationen
F. Stadlbauer, T. Koch, V. Archodoulaki:
"Optimierung der Mess- und Auswertemethodik zur Charakterisierung des Ermüdungsverhaltens von Elastomeren";
Vortrag: Tagung Werkstoffprüfung 2013,
Neu-Ulm;
28.11.2013
- 29.11.2013; in: "Fortschritte in der Werkstoffprüfung für Forschung und Praxis",
H. Christ (Hrg.);
Verlag Stahleisen GmbH,
(2013),
ISBN: 978-3-514-00806-9;
S. 151
- 156.
Zusätzliche Informationen
F. Stadlbauer, T. Koch, F. Planitzer, W. Fidi, V. Archodoulaki:
"Advanced evaluation of the influence of material parameters and sample geometries on the crack growth in rubber";
Vortrag: Polymeric Materials 2012,
Halle (Saale);
12.09.2012
- 14.09.2012; in: "Polymeric Materials 2012",
(2012),
6 S.
Zusätzliche Informationen
F. Stadlbauer, T. Koch, F. Planitzer, W. Fidi, V. Archodoulaki:
"Advanced setup for the evaluation of crack growth in rubber: influence of sample geometry and filler content tested in tension-compression mode";
Vortrag: 10th Fall Rubber Colloquium,
Hannover;
07.11.2012
- 09.11.2012; in: "10th Fall Rubber Colloquium",
(2012),
9 S.
Vorträge und Posterpräsentationen (ohne Tagungsband-Eintrag)
V. Archodoulaki:
"Technische Herausforderungen beim Kunststoffrecycling";
Vortrag: e·nova 2020 - internationale Konferenz - 26./27. November 2020,
FH Burgenland;
26.11.2020
- 27.11.2020.
V. Archodoulaki, M. Huber, M Gahleitner:
"Occurrence of microplastics in the aquatic environment";
Poster: CIS 2019,
Italien;
28.08.2019
- 30.08.2019.
V. Archodoulaki, T. Koch, S. Lüftl, C. Schoberleitner:
"Werkstoffauswahl";
Vortrag: Pressekonferenz,
Bratislava, Slowakei;
28.07.2010.
Zusätzliche Informationen
M. Bonta, S. Fröhlich, M. Hafner, E. Pittenauer, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"MALDI-RTOF mass spectrometric analysis of lipid compounds in synovial fluid separated by 2D thin layer chromatography";
Poster: 2nd Graz Lipid Mass Spec Meeting,
Graz;
06.03.2012
- 07.03.2012.
M. Bonta, S. Fröhlich, M. Hafner, E. Pittenauer, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"MALDI-RTOF-MS analysis of lipid compounds in synovial fluid separated by two-dimensional thin layer chromatography";
Vortrag: MassSpec-Forum-Vienna-2012,
Wien;
21.02.2012
- 22.02.2012.
B. Duscher, A. Laska, A. Örs Ünsal, V. Archodoulaki:
"Structural Modification of Conventional and Crosslinked PE-UHMW Acetabular Liners due to in vivo Time and Load";
Vortrag: FBPS '15 - 11th Symposium on Frontiers in Biomedical Polymers,
Riva del Garda, Idataly;
08.07.2015
- 11.07.2015.
Zusätzliche Informationen
B. Duscher, A. Zisser, F. Kamleitner, T. Koch, V. Archodoulaki:
"Evaluation of stabilizer and additive content of post-consumer-polypropylene waste and their influence on new concepts of polypropylene-upcycling";
Poster: Polymer Processing Society Conference 2015,
Graz;
21.09.2015
- 25.09.2015.
Zusätzliche Informationen
S. Fröhlich, E. Claude, M. Kennedy, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"Correlating UHMW-PE cross-linking with biomolecular induced material modifications by means of MALDI-RTOF imaging mass spectrometry";
Poster: Ourence Conference on Imaging Mass Spectrometry,
Ourence, Spain;
03.09.2012
- 05.09.2012.
S. Fröhlich, M. Kennedy, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"Correlating UHMW-PE degradation and modification with biomolecular adsorption by means of MALDI imaging mass spectrometry";
Poster: 5th Vienna Biomaterialsymposium,
Wien;
19.11.2012
- 21.11.2012.
S. Fröhlich, T. Luider, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"MALDI-TOF mass spectrometry imaging - A tool to investigate time-dependent biomolecule adsorption in correlation to induced polymer changes on UHMW-PE hip joints";
Vortrag: 5th Vienna Biomaterialsymposium,
Vienna;
19.11.2012
- 21.11.2012.
S. Fröhlich, R. Markut-Kohl, V. Archodoulaki, D. Kerjaschki, G. Allmaier, M. Marchetti-Deschmann:
"UHMWPE joint implants - investigating simulated synovial compound adsorption by MALDI imaging mass spectrometry";
Vortrag: 9th Austrian Proteomics Research Symposium - Special focus on clinical proteomics,
Wien (eingeladen);
08.11.2011
- 09.11.2011.
S. Fröhlich, S. Schrottshammer, E. Claude, M. Kennedy, V. Archodoulaki, G. Allmaier, M. Marchetti-Deschmann:
"Time dependent in vitro adsorption of synovial compounds on ultra-high molecular weight polyethylene investigated by MALDI imaging mass spectrometry";
Poster: 10th Austrian Proteomic Research Symposium,
Graz;
24.09.2012
- 26.09.2012.
M. Marchetti-Deschmann, J. Galehr, P. Rigger, V. Archodoulaki, G. Allmaier:
"Imaging mass spectrometry of ultrahigh molecular weight polyethylene (UHMW-PE) joint explants";
Vortrag: MassSpecForum Vienna 2011,
Wien;
22.02.2011
- 23.02.2011.
M. Petrica, B. Duscher, T. Koch, V. Archodoulaki:
"Studies on Tribological Behavior of PEEK and PE-UHMW";
Poster: Polymer Processing Society Conference 2015,
Graz;
21.09.2015
- 25.09.2015.
Zusätzliche Informationen
S. Stanic, F. Kamleitner, B. Duscher, T. Koch, S. Knaus, V. Archodoulaki:
"Innovative Upcycling of Polypropylene Post Consumer Waste";
Poster: International Symposium - Science to support circular economy,
TU Wien / Kuppelsaal;
19.09.2018.
Habilitationsschriften
V. Archodoulaki:
"Eigenschaftsänderungen von Polyoxymethylenen induziert durch Verarbeitung, Alterung und Recycling";
TU Wien/Fakultät für Maschinenwesen und Betriebswissenschaften,
2005.
Dissertationen (eigene und begutachtete)
S. Cirak:
"Wasserbasierende Isolierlacksysteme";
Betreuer/in(nen), Begutachter/in(nen): S. Knaus, V. Archodoulaki, H. Hoffmann;
Institut für Angewandte Synthesechemie,
2018;
Rigorosum: 19.12.2018.
Zusätzliche Informationen
C. Fleischberger:
"Production and evaluation of active antimicrobial polymer films for food packaging";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, I. Steiner;
Werkstoffwissenschaft und Werskstofftechnologie,
2013;
Rigorosum: 21.08.2013.
S. Fröhlich:
"The impact of bio-compartments on polymers used for artificial bio-replacement by mass spectrometry imaging and conventional bio-analytics";
Betreuer/in(nen), Begutachter/in(nen): M. Marchetti-Deschmann, V. Archodoulaki;
Chemische Technologien und Analytik,
2014;
Rigorosum: 25.04.2014.
Zusätzliche Informationen
P. Gauss:
"Advanced additives for radical photopolymerization";
Betreuer/in(nen), Begutachter/in(nen): R. Liska, J. Fleig, V. Archodoulaki;
Institut für Angewandte Synthesechemie,
2019;
Rigorosum: 26.03.2019.
Zusätzliche Informationen
R. Grab:
"Umweltgerechtes Diktiergerät";
Betreuer/in(nen), Begutachter/in(nen): W. Wimmer, V. Archodoulaki;
Institut für Konstruktionswissenschaften und Technische Logistik E 307,
2010.
F. Kamleitner:
"Innovative Upcycling of Polypropylene";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, C. Paulik, S. Knaus;
Werkstoffwissenschaft und Werkstofftechnologie - E308,
2017;
Rigorosum: 13.12.2017.
Zusätzliche Informationen
E. Karaagac:
"Blends of post-consumer recycled polypropylene (PP)/polyethylene (PE): rheology, morphology, and mechanics";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, S. Knaus, A. Bismarck;
Werkstoffwissenschaft,
2021;
Rigorosum: 29.11.2021.
C. Karg:
"Verschleißminimierung in der Einzugszone von Nutbuchsenextrudern";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, F. Franek;
Werkstoffwissenschaft und Werkstofftechnologie,
2011;
Rigorosum: 15.09.2011.
Zusätzliche Informationen
M. Kellner:
"Entwicklung neuer Materialien für protonenleitende Membranen in Brennstoffzellen";
Betreuer/in(nen), Begutachter/in(nen): R. Liska, V. Archodoulaki;
Institut für Angewandte Synthesechemie,
2013;
Rigorosum: 30.10.2013.
P. Knaack:
"Fudamental Studies on Tailoring Polyolefines for Modern Manufacturing Techniques";
Betreuer/in(nen), Begutachter/in(nen): S. Knaus, V. Archodoulaki;
IAS,
2015;
Rigorosum: 26.11.2015.
X. Meng:
"Preparation of PP graft copolymers and compatibilized PP/EVOH-Blends by reactive extrusion";
Betreuer/in(nen), Begutachter/in(nen): S. Knaus, V. Archodoulaki;
Institut für Angewandte Synthesechemie,
2013;
Rigorosum: 30.10.2013.
L. Nguyen Pham Duy:
"Properties and Applications of Epoxy-Functional Polyolefins Synthesized by Reactive Extrusion";
Betreuer/in(nen), Begutachter/in(nen): S. Knaus, V. Archodoulaki;
Institut für Angewandte Synthesechemie,
2012;
Rigorosum: 05.03.2012.
A. Örs-Ünsal:
"Comparative Studies of Conventional and Cross-linked Implants and Explants";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, G. Pinter, O. Muratoglu;
Werkstoffwissenschaft und Werkstofftechnoloige,
2020;
Rigorosum: 11.09.2020.
I. Panaitescu:
"Long-term durability studies of glass fiber reinforced polyurethane under operational environments";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, S.G. Pantelakis, W. Stadlbauer;
Werkstoffwissenschaft,
2019;
Rigorosum: 28.02.2019.
Zusätzliche Informationen
M. Petrica:
"Study of the wear processes and tribological relevant properties of engineering thermoplastics";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, B. Langer;
Werkstoffwissenschaft und Werkstofftechnologie,
2016;
Rigorosum: 20.09.2016.
M. Rodríguez-Hortalá:
"Characterisation of Defects in Carbon Fibre Reinforced Polymer (CFRP) Laminates and Pultruded Profiles";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, R. Schledjewski;
Institut fuer Werkstoffwissenschaft und Werkstofftechnologie,
2013;
Rigorosum: 22.02.2013.
Zusätzliche Informationen
C. Schoberleitner:
"Entwicklung einer Werkstoffformulierung zur Robotersanierung von undichten Muffen in Trinkwasserversorgungsleitungen";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, R. Liska;
Institut für Werkstoffwissenschaft und Werkstofftechnologie,
2013;
Rigorosum: 20.11.2013.
Zusätzliche Informationen
S. Seichter:
"Fatigue Behaviour of Rubber Blends and Rubber-Textile Composites Considering Application-Relevant Aspects";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2017;
Rigorosum: 26.04.2017.
Zusätzliche Informationen
F. Stadlbauer:
"Ermüdung und Risswachstum von Elastomerwerkstoffen unter praxisrelevanter Beanspruchung";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, G. Heinrich;
Institut für Werkstoffwissenschaft und Werkstofftechnologie,
2014;
Rigorosum: 17.02.2014.
Zusätzliche Informationen
T. Staffenberger:
"Material- und Verfahrensentwicklung thermoplastischer Stützkörper für die Fertigung von Faserverbund-Hohlbauteilen im RTM-Infusionsverfahren";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, R. Schledjewski;
Werkstoffwissenschaft und Werkstofftechnologie,
2014;
Rigorosum: 04.09.2014.
S. Yeganeh:
"Effect of ethanol content fuels on the engineering thermoplastics";
Betreuer/in(nen), Begutachter/in(nen): V. Archodoulaki, S. Knaus;
Werkstoffwissenschaft und Werkstofftechnologie,
2014;
Rigorosum: 27.02.2014.
Zusätzliche Informationen
Diplom- und Master-Arbeiten (eigene und betreute)
A. Ahmadi:
"Einfluss von Stabilisatoren auf die mechanischen und thermischen Eigenschaften des Polypropylens während der Alterung";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnoloige,
2020;
Abschlussprüfung: 31.08.2020.
S. Birk:
"Studies about the consolidation behavior of hybrid bicomponent fiber preforms";
Betreuer/in(nen): V. Archodoulaki;
Werkstoffwissenschaft,
2019;
Abschlussprüfung: 25.09.2019.
F. Bittner:
"Mechanisches Recycling von Polystyrol - Herausforderungen und Möglichkeiten";
Betreuer/in(nen): V. Archodoulaki, M. Seier;
Werkstoffwissenschaft,
2021;
Abschlussprüfung: 28.06.2021.
C. Böck:
"Bruchmechanische Untersuchungen an PE-UHMW";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2015;
Abschlussprüfung: 30.11.2015.
E. Bumbaris:
""The Effect of Bacterial Cellulose on Flax Fibre Thermoplastic Composites"";
Betreuer/in(nen): A. Bismarck, V. Archodoulaki;
Institute of Materials Chemistry & Research UNI WIEN,
2017;
Abschlussprüfung: 06.11.2017.
Zusätzliche Informationen
R. Chary:
"Kompatibilisierungsmöglichkeiten von PET-PE-basierten Mehrschicht- Verpackungen";
Betreuer/in(nen): V. Archodoulaki, M. Seier;
Werkstoffwissenschaft,
2021;
Abschlussprüfung: 15.11.2021.
K. Danzl:
"Compatibilisierung von PET/PE Blends im Hinblick auf Recycling von Mehrschichtfolien";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2020;
Abschlussprüfung: 26.02.2020.
S. Dworak:
"Machbarkeitsstudie zum Heißverpressen von bepinnten Metallen mit glasfaserverstärkten Thermoplasten";
Betreuer/in(nen): T. Koch, V. Archodoulaki;
Werkstoffwissenschaft und Werskstofftechnologie,
2013;
Abschlussprüfung: 22.11.2013.
M. Eder:
"Bestimmung der Wärmeleitfähigkeit von Kunststoffen mittels DSC und Thermografie";
Betreuer/in(nen): T. Koch, V. Archodoulaki;
Werkstoffwissenschaft,
2021;
Abschlussprüfung: 20.12.2021.
R. Eder:
"Strangaufweitung von Kautschukmischungen in Abhängigkeit von ihren viskoelastischen Materialeigenschaften und verfahrenstechnischen Parametern der Rollerhead-Anlage";
Betreuer/in(nen): V. Archodoulaki;
Werkstoffwissenschaft und Werkstofftechnologie,
2016;
Abschlussprüfung: 29.09.2016.
B. Feyerabend:
"Alternative Polymerwerkstoffe zum PTFE. Eigenschaftsspezifische und anwendungsorientierte Betrachtungen unter dem Aspekt einer möglichen Werkstoffsubstitution";
Betreuer/in(nen): V. Archodoulaki, R. Liska;
Werkstoffwissenschaft und Werkstofftechnologie,
2013;
Abschlussprüfung: 25.02.2013.
P. Friedl:
"Untersuchung ausgewählter Kieselerden als potenzielle Füllstoffe in lichthärtenden 3D-Druckharzen";
Betreuer/in(nen): J. Stampfl, V. Archodoulaki;
Institut für Werkstoffwissenschaft und Werkstofftechnologie,
2018;
Abschlussprüfung: 12.12.2018.
Zusätzliche Informationen
G. Gottlieb:
"Einfluss verschiedener Peroxide auf die Langkettenverzweigung von Polypropylen";
Betreuer/in(nen): V. Archodoulaki, S. Stanic;
Werkstoffwissenschaft,
2020;
Abschlussprüfung: 23.09.2020.
Zusätzliche Informationen
T. Gustenau:
"Einfluss von Antioxidantien auf die Alterung von Polyethylen";
Betreuer/in(nen): V. Archodoulaki, B. Duscher;
Werkstoffwissenschaft und Werkstofftechnologie,
2016;
Abschlussprüfung: 14.07.2016.
Zusätzliche Informationen
C. Haim:
"Charakterisierung von Kunststoffverpackungen zur Evaluierung von Recycling Potentialen";
Betreuer/in(nen): V. Archodoulaki, M. Seier;
Werkstoffwissenschaft,
2022;
Abschlussprüfung: 24.03.2022.
Zusätzliche Informationen
S. Hohenauer:
"Optimierung des Prozesses zur Herstellung einer Kautschukmischung mittels Design of Experiments";
Betreuer/in(nen): V. Archodoulaki;
Werkstoffwissenschaft und Werkstofftechnologie,
2016;
Abschlussprüfung: 12.04.2016.
M. Humer:
"Charakterisierung von Verbundwerkstoffen mit thermoplastischer Matrix";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2016;
Abschlussprüfung: 29.09.2016.
A. Jahn:
"Microplastic in our environment: A review of the biggest perpetrators and possible solutions";
Betreuer/in(nen): V. Archodoulaki;
Werkstoffwissenschaft und Werkstofftechnoloige,
2020;
Abschlussprüfung: 17.06.2020.
Zusätzliche Informationen
C. Jettel:
"Hygienische Aufbereitung von Kunststoffen und deren Auswirkung auf die Materialeigenschaften";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft,
2019;
Abschlussprüfung: 16.07.2019.
M. Kapfhammer:
"Aging of reinforced thermoplastic pipes under extreme environmental conditions";
Betreuer/in(nen): T. Koch, V. Archodoulaki;
Werkstoffwissenschaft und Werkstofftechnologie,
2020;
Abschlussprüfung: 19.05.2020.
Zusätzliche Informationen
E. Karaagac:
"Casting and Curing Process Optimization of Epoxy Resin used in Electromagnetic Track Brakes";
Betreuer/in(nen): V. Archodoulaki;
Werkstoffwissenschaft und Werkstofftechnologie,
2015;
Abschlussprüfung: 26.11.2015.
F. Kerres:
"Entwicklung, Aufbau und Test einer Zugprüfeinrichtung für in situ Deformationsverusche von Kunststoffen unter dem FTIR Mikroskop";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2014;
Abschlussprüfung: 18.02.2014.
C. Klösch:
"Degradationsverhalten von Polypropylen unter Berücksichtigung von verschiedenen Alterungsaspekten";
Betreuer/in(nen): V. Archodoulaki, M. Seier;
Werkstoffwissenschaft,
2022;
Abschlussprüfung: 24.03.2022.
Zusätzliche Informationen
R. Kodras:
"Machbarkeitsstudie zum Heißpressen von bepinnten Metallen mit glasfaserverstärktem Polyamid";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2015;
Abschlussprüfung: 27.03.2015.
H. Kovacevic:
"Tribologische Untersuchungen an Polymeren";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2019;
Abschlussprüfung: 20.11.2019.
Zusätzliche Informationen
M. Kuhn:
"Entwicklung eines optischen Systems zur Evaluierung des Ermüdungsrissverhaltens von Elastomerwerkstoffen";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Institut für Werkstoffwissenschaft und Werkstofftechnologie,
2016;
Abschlussprüfung: 23.06.2016.
Zusätzliche Informationen
B. Liedl:
"Printed and laser-structured impedance sensors in glue lines";
Betreuer/in(nen): A. Bismarck, V. Archodoulaki;
Universität Wien Institute of Materials Chemistry & Research,
2018;
Abschlussprüfung: 23.11.2018.
M. Merola:
"Mechanical and tribological characterization of GFRP and CFRP laminates obtained by VARTM";
Betreuer/in(nen): V. Archodoulaki, A. Ruggiero;
Werkstoffwissenschaft und Werkstofftechnologie + University of Salerno,
2014;
Abschlussprüfung: 18.11.2014.
Zusätzliche Informationen
M. Mosbeck:
"Material-scientific analysis of virgin PE-UHMW acetabular bearings";
Betreuer/in(nen): V. Archodoulaki, E. Kozeschnik;
Werkstoffwissenschaft und Werkstofftechnologie,
2011;
Abschlussprüfung: 02.05.2011.
Zusätzliche Informationen
A. Mudaffer:
"Apparatur zur Bestimmung mechanischer Eigenschaften mittels eines kleinen Stanzgerätes (Small Punch)";
Betreuer/in(nen): V. Archodoulaki, B. Duscher;
Werkstoffwissenschaft und Werkstofftechnologie - E308,
2017;
Abschlussprüfung: 16.11.2017.
Zusätzliche Informationen
H. Nguyen Thu:
"printable formulations for macroporous polymers useful for battery applications";
Betreuer/in(nen): A. Bismarck, V. Archodoulaki;
Universität Wien Institute of Materials Chemistry & Research,
2018;
Abschlussprüfung: 04.05.2018.
A. Pappas:
"Correlation of structural parameters, thermal and mechanical properties of UHMWPE with wear rate in hip implant applications";
Betreuer/in(nen): V. Archodoulaki, P. Tarantili;
Werkstoffwissenschaft und Werkstofftechnologie,
2011;
Abschlussprüfung: 27.06.2011.
Zusätzliche Informationen
L. Pasler:
"Charakterisierung von Mehrschicht-Verpackungen in Hinblick auf den weiterführenden Recycling-Prozess";
Betreuer/in(nen): V. Archodoulaki;
Werkstoffwissenschaft,
2019;
Abschlussprüfung: 27.02.2019.
Zusätzliche Informationen
K. Pereira Alvim:
"novel electrodes for structural batteries";
Betreuer/in(nen): A. Bismarck, V. Archodoulaki;
Universität Wien Institute of Materials Chemistry & Research,
2018;
Abschlussprüfung: 04.06.2018.
H. Pesendorfer:
"Morphologische Analyse von Faserverbunden mittels Schliffverfahren";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2015;
Abschlussprüfung: 19.06.2015.
J. Pesendorfer:
"Upcycling von Polystyrol und Polypropylen Joghurtbechern";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft,
2019;
Abschlussprüfung: 27.02.2019.
Zusätzliche Informationen
M. Redl:
"Entwicklung eines CFK-Standrohrs für die Verwendung in Upside-Down-Motorrad-Teleskopfedergabeln";
Betreuer/in(nen): V. Archodoulaki, R. Knasmillner;
Werkstoffwissenschaft und Werkstofftechnologie,
2015.
J. Schlossnikl:
"Modifizierungsmöglichkeiten von Post Consumer Abfällen bestehend aus Polypropylen";
Betreuer/in(nen): V. Archodoulaki, S. Stanic;
Werkstoffwissenschaft,
2021;
Abschlussprüfung: 19.05.2021.
Zusätzliche Informationen
C. Schoberleitner:
"Werkstoffuntersuchungen an Hüftpfannenexplantaten - Ultrahochmolekulares Polyethylen in der klinischen Anwendung";
Betreuer/in(nen): V. Archodoulaki;
E308,
2010;
Abschlussprüfung: 23.06.2010.
M. Seier:
"Einfluss verschiedener Blends auf die Langkettenverzweigungen von Polypropylen";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2019;
Abschlussprüfung: 12.12.2019.
Zusätzliche Informationen
I. Steinberger:
"Polyethylen-Polypropylen Blends: Einfluss der Peroxidzumischung";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2020;
Abschlussprüfung: 23.04.2020.
Zusätzliche Informationen
C. Thoma:
"Upcycling von Polypropylen: Herstellung von Schäumen";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie - E308,
2018;
Abschlussprüfung: 29.01.2018.
Zusätzliche Informationen
F. Weichselbraun:
"Degradationsmechanismen in verschiedenen Polyethylenen nach Recyclingprozessen";
Betreuer/in(nen): V. Archodoulaki, J. Roitner;
Werkstoffwissenschaft,
2021;
Abschlussprüfung: 15.12.2021.
A. Zisser:
"Einfluss von Oxidations- und UV-Stabilisatoren auch die mechanischen und thermischen Eigenschaften des Polypropylens";
Betreuer/in(nen): V. Archodoulaki, B. Duscher;
Werkstoffwissenschaft und Werkstofftechnologie,
2016;
Abschlussprüfung: 27.01.2016.
Zusätzliche Informationen
S. Zoppoth:
"Upcycling von Polypropylen: Herstellung von Schäumen";
Betreuer/in(nen): V. Archodoulaki, T. Koch;
Werkstoffwissenschaft und Werkstofftechnologie,
2017;
Abschlussprüfung: 17.05.2017.
Zusätzliche Informationen
Wissenschaftliche Berichte
V. Archodoulaki, M. Marchetti-Deschmann:
"GENder-related Implant Examination";
Bericht für FFG;
2013;
47 S.
Zusätzliche Informationen